ABB ACS350 MANUAL PDF

View and Download ABB ACS user manual online. ACS Inverter pdf manual download. Document library, contact your local ABB representative. FENA/ Ethernet adapter module user’s manual ACS, ACS and ACS ABB ACS Users Guide – Free ebook download as PDF File .pdf), Text File . txt) or read book ACS Drives 22 kW 30 HP User’s Manual.

Author: Yosida Malasar
Country: Cayman Islands
Language: English (Spanish)
Genre: Music
Published (Last): 15 November 2008
Pages: 33
PDF File Size: 15.62 Mb
ePub File Size: 1.18 Mb
ISBN: 435-2-75580-938-9
Downloads: 31857
Price: Free* [*Free Regsitration Required]
Uploader: Netaxe

User Macros User macros In addition to the standard application macros, it is possible to create three user macros. The upper case boldface text refers to the states shown in the following block diagram ABB Drives profile Control Word parameter Page The following table and the state diagram later in this section describe the Status Word content for the ABB Drives profile.

Make sure that dust from drilling does not enter the drive during the installation.

PID Control macro This macro provides parameter settings acz350 closed-loop control systems such as pressure control, flow control, etc. Reference trimming In reference trimming, the external reference is corrected depending on the measured value of a secondary application variable.

Fieldbus interface as the source for inverted Run Enable signal Run Disablei. See also section State shifts on page Reference Types And Processing Reference types and processing The drive can accept a variety of references in addition to the conventional analog input and control panel signals. Tightening torque is 0. COMM Fieldbus interface as the source for the fault reset signal, i.

ABB ACS350 – 7.5kW 230V 3ph to 3ph – AC Inverter Drive Speed Controller

The dimensions are given in millimeters and [inches]. Page Drive control parameters After the fieldbus communication has been set up, the drive control parameters listed in the table below should be checked and adjusted where necessary.

One push button controls the drive through the whole cycle: If ignored, physical injury or death may follow, or damage may occur to the drive, motor or driven equipment. Assistants Mode Assistants mode When the drive is first powered manuzl, the Start-up Assistant guides you through the setup of the basic parameters. See chapter Application macros.

  CATYLAC CATALOG PDF

Operation time scheme The time scheme below illustrates the operation of the brake control function. Set the motor data to exactly the same value as on the motor nameplate.

ABB ACS USER MANUAL Pdf Download.

The speed is determined by the average speed over the previous 10 seconds. The following table and the state diagram later in this section describe the Status Word content for the ABB Drives profile. Control can also be switched to speed control using a digital input. Copy Mode Copy mode The Basic Control Panel can store a full set of drive parameters and up to three user sets of drive parameters to the control panel.

Page 82 How to upload and download parameters For the upload and download functions available, see above. Ratings on page Plan the installation: Torque Control Macro Torque Control macro This macro provides parameter settings for applications that require torque control of the motor.

ABB ACS350 – 0.75kW 400V 3ph to 3ph – AC Inverter Drive Speed Controller with Keypad

Speed Control Performance Figures Speed control performance figures The table below shows typical performance figures for speed control. Page The drive can be connected to an external control system via a fieldbus adapter or embedded fieldbus. User macros In addition to the standard application macros, it is possible to create three user macros. Drive is not ready. Abbb section Speed compensated stop on page Underload Protection Underload Protection Loss of motor load may indicate a process malfunction.

Holding Registers Parameter sets, control, status and reference values are mapped as holding registers. For other parameters, the default values are the same for all macros. The Fieldbus Control Interface The fieldbus control interface The communication between a fieldbus system and the drive consists of bit input and output data words with ABB Drives profile and bit input and output words with DCU profile.

  IEC 825-1 PDF

When the motor speed falls below the sleep level, the counter starts. The minimum input signal runs the motor at the maximum reference in the reverse direction, the maximum input at the maximum wcs350 in the forward direction.

Example 1 50 Hz 0 Hz Hz Seq. Installation and commissioning flowchart Task Identify the frame size of your drive: Mounting the drive Mount the drive Note: The symbols are described below the table. Available for two seconds at manul, otherwise as long as 2max allowed by the drive temperature.

Falling edge of inverted digital input DI1: Page nanual How to get help Step Action Display Press to read the context-sensitive help text for the item that is highlighted. The motor and control cables are selected as specified in this manual. The brake is re-opened when the requirements set by parameters The function is useful in applications where a smooth and quick mnual is essential. Select the application macro parameter The requirements are easily met with mankal copper or aluminium shield.

Initially, the panel is in the Output mode, where you can Never attempt to repair a manuxl drive; contact your local ABB representative or Authorized Service Center for replacement. Table Of Contents Parameters — complete descriptions Supervision status can be monitored with relay or transistor output.

Thermistor Contact your local ABB representative. Parameter mode In the Parameter mode, you can: Contact your local ABB representative for the approved breaker types and supply network characteristics. In the following examples the reference is in rpm. Using the control panel to do these tasks is explained briefly in this chapter.

Author: admin