Interchangeability of Alliance Tenna-Rotors. Wire Charts .. Wire Chart for Extra Long Runs of Cable Use of 2 or more Controls on One Rotor. The U Tenna-Rotor includes a control box. (FIG. 1), rotor (FIG. 2), mast clamp (FIG. 3) and one hardware bag containing U-bolts, terminal cover. GENERAL INFORMATION. The Alliance Tenna-Rotor® Model U is a fully auto- matic unit. The control knob is turned to the desired di- rection and the rotor .
|Published (Last):||13 May 2015|
|PDF File Size:||19.14 Mb|
|ePub File Size:||13.76 Mb|
|Price:||Free* [*Free Regsitration Required]|
All trademarks, copyrights, patents, and other rights of ownership to images and text used on the RF Cafe website are hereby acknowledged.
It is possible for the wind or some other force to tsnna-rotor the antenna shaft from turning as the worm gear tries to turn, which would strain or stall the motor, but it cannot be forced forward or backward.
The seller found it in his father’s attic. Do you remember the signature ker-chunk, ker-chunk sound of that solenoid turning the allliance dial?
My primary interest is being able to pick up radio stations since I rarely watch TV.
Tenna-Rotor Controller ATR
The rotator box motor rotation direction is determined by which set of field coils is energized by the control box; i. There are a few companies AudiovoxChannel MasterRCA who still sell antenna rotators that are modern transistorized units with digital readouts.
Customer reviews of the new units reveal dissatisfaction with the weakness of the rotator unit that mounts on the antenna mast, and the inability of it to prevent the antenna from being rotated in a strong wind no brake or poor brake.
Topical Smorgasbordanother manifestation of Factoids, are be found on these pages: Topical Smorgasbordanother manifestation of Factoids, are be found on these pages:. If you grew up in the era of rooftop television antennas, then there is a tenna-ortor chance you are familiar with the electromechanical allance pointing systems that were often installed as well.
Mechanical drawings were located on the Norm’s Rotor Service website and Bougetoline has schematics, so I thank them for that. A huge collection of my ‘Factoids’ can be accessed from my ‘ Kirt’s Cogitations ‘ table of contents. Load bearing surfaces are simple bushings rather than tenna-rotir bearings, but the shaft will turn so little in a typical lifetime of use that it shouldn’t matter.
Vintage Alliance Tenna Rotor Antenna Control Model T12 NESWN Genie Ham Radio | eBay
A worm drive is like a mechanical diode in that only a rotation of the worm input motor drive shaft will cause the output shaft to rotate. I waited for many months for such an example to appear at a decent price because of wanting to document the entire system as originally supplied, so it was disappointing to have the cover missing. Sometime I couldn’t get even relatively nearby stations no matter the orientation.
Control and feedback is about as simple as it gets with a motor turning the antenna mast and a tenja-rotor in the control box that advances the dial as the antenna rotates. A half-wave folded dipole has been used for many years, but because of where my house is located reception quality varies throughout the year and according to the weather.
Doing so wouldn’t get me the classic antenna-on-the-roof look I alliancee, but it would keep the antenna and rotator unit safe from the weather and it would probably last the rest of my lifetime.
A photo of the cover will be added here when it is available. I plan to make the best of the situation and exploit my local library’s MakerSpace facility’s 3D printer to make a replacement.
Often time I would need to re-orient one or both sides of the dipole to get good pickup. All pertain to topics that are related to the general engineering and science theme of RF Cafe. Everything looked good except the grease in the rotator was hard caked and needed tenna-totor be cleaned off and replaced, which I did.
As you can see in the photos, the cast aluminum parts are very robust. Applying a torque to the output shaft, which is connected to the antenna, cannot cause the worm gear to rotate.
Vintage Alliance Model U Tenna-Rotor Installation (Kirt’s Cogitation #) – RF Cafe
Cams on both ends open and close contacts as required. Lower quality copies are posted here in case they ever disappear from Norm’s Rotor Service website.
When I first began planning an antenna installation, I was going to put it on the roof like in the old days, but I tenha-rotor I would try it in the garage attic first to see how well it worked there.
That was one of the reasons I wanted this old system, just to hear that sound again. Its primary purpose was to provide alliancee with ready access to commonly needed formulas and reference material while performing my work as an RF system and circuit design engineer.