AMERICAN AUDIO V1000 PDF

Results 1 – 34 Valuation Report for Used V Power Amplifier by American Audio (Specs: 2 ( Stereo), x 2 @ 8, Bridgeable). Output Power: W RMS Per Channel @ 4 Ohms, 1kHz, % THD W RMS Per Channel @ 8 Ohms, 1kHz, % THD – Bridge Mode, Mono W RMS. Download AMERICAN AUDIO V V SCH service manual & repair info for electronics experts.

Author: Toktilar Dainris
Country: Namibia
Language: English (Spanish)
Genre: Health and Food
Published (Last): 21 February 2005
Pages: 46
PDF File Size: 10.89 Mb
ePub File Size: 13.13 Mb
ISBN: 980-1-81884-372-6
Downloads: 37356
Price: Free* [*Free Regsitration Required]
Uploader: Maut

Turn your equipment on your amplifier should always be the last item you turn on.

AMERICAN AUDIO V1000 POWER AMP AMPLIFIER 1000 WATTS NR!

When the input signal decreases enough that clipping ends, the limiter will deactivate and cease its gain reduction. Clipping should be kept to a reasonable minimum.

Turn your amp on. Americann XLR jack is configured as follows; Pin three positive, pin two negative, pin one ground. If your speaker lines short, the amplifier automatically detects this problem and discontinues operation for that channel.

If the breaker continues to pop, stop using the amplifier and contact customer service. The amplifier can operate at practically any power level without risk of overheating.

Connect a XLR cable to the input of channel one.

Fuse Holder – This holder houses the external fuse. Risiko – Elektrischer Schlag! It’s a community-based project which helps to repair anything.

  COSMOGONIA MASONICA PDF

This amplifier is designed to mount americzn a standard 19″ rack. If the “CLIP ” indicator flashes occasionally, the amplifier is approaching its maximum long-term power capacity.

V Power Amplifier by American Audio Valuation Report by

Diagram 10 When connecting your speakers to the amplifier using bare wire; Unscrew the red and black caps on the binding post, be sure not to completely remove or unscrew the red and black caps. This fan is used to cool the internal parts of the amplifier when in use.

See page 9 for more details on input configuration. Channel 2 Frequency Adjustment.

When connecting your speakers to the amplifier using banana jacks; Be sure that the red and black caps on the binding post are tighten down completely. The power-supply cord or the plug has been damaged.

Use channel two positive output terminal for the negative connection and the channel one positive output terminal for the positive connection. Service Hours are Monday through Friday 9: In the event of an electrical overload the breaker will pop-out.

Connect an input signal to channel one. The appliance has been exposed to rain or water.

Operating instructions AMERICAN AUDIO V PLUS |

Bridged-Mono Mode Caution – The voltage across the output terminals of a bridged Vplus series amplifier may equal or exceed V volts RMS and may be as high as volts. The fixture does not appear to operate normally or exhibits a marked xmerican in performance. Connections are made to Channels 1 and aerican output’s for stereo mode or across the red terminals of Channels 1 and 2 for Mono Bridge Mode. Below rated output, 8 ohms americam, unweighted dB, unweighted dB, akdio dB, unweighted dB, unweighted Power Consumption: These fans are used to cool the internal parts of the amplifier.

  DIE HETEROTOPIEN FOUCAULT PDF

During signal overload, the limiter will reduce the input audio signal enough to minimize the amount of clipping. Uadio 1 filters is control by dip switch 1 and channel 2 filter is controlled by dip switch 4.

Mono bridge operation connections will follow the above descriptions however, when operating in mono bridge operation the speaker connections will run between the two positive red leads. Configuring the Low Cut Filter: During excessive clipping the limiter will reduce the audio signal enough to minimize the amount of clipping.

Never plug your amplifier in to a wall outlet that does not match the required voltage of your amplifier, serious damage may occur to your unit.

Ensuring proper polarity will avoid speakers being out of phase, that can cause a loss of bass response.

Author: admin