Shop for American DJ V Power Amplifier and more at everyday discount prices with free shipping over $50* on – Your Online Store!. Buy the ADJ V Amplifier at PlanetDJ. Low VIP Pricing, Financing and Free Shipping available. American Audio | V | User manual | American Audio V User manual American Audio® – – V Vplus Series Amplifiers Power.
|Published (Last):||12 November 2005|
|PDF File Size:||15.83 Mb|
|ePub File Size:||8.49 Mb|
|Price:||Free* [*Free Regsitration Required]|
During excessive clipping the limiter will reduce the audio signal enough to minimize the amount of clipping. The limiter reduces the average output level when the signal begins to distort, this process is designed to reduce distortion and protect the speakers.
Be sure that supplied voltage matches that of the required voltage of you americxn.
Insert bare wire into the binding post and tighten. A balanced connection is recommended for cable runs longer that 20ft. During zmerican level output the fans run at normal speeds.
Channel 2 Frequency Adjustment.
American DJ V 2 Channel Professional Stereo Amplifier | eBay
Use the channel one gain to regulate your amplifier output. Insert the banana jacks into the caps of the binding post, be sure that the banana jack is inserted securely to avoid the risk of it popping out. Before using this amplifier, read the user manual for further warnings.
Power Switch – This switch controls the units main power. Typical speaker output using bare wire. Connect a XLR cable to the input of channel one.
American DJ V3000 2 Channel Professional Stereo Amplifier
Low Cut Frequency Selector – When the Low Cut Filter is activated, dip switches 2 channel americwn and amedican channel 2 will control the frequency roll-off. The dip switches on the rear panel allows you to enable or disable the filter for each channel, as well as adjust either a 50Hz or 30 Hz cut-off. You may also visit us on the web at www. Rear mounting the unit is especially recommended if the unit is to mounted into a mobile rack.
Be sure not to operate your amplifier below the minimum load ratings to reduce the risk of overheating problems.
American Audio V3000/V2000 Stereo Amplifier User Manual
Never block the fan in any way or g3000 in an enclose rack, doing so may cause the amplifier to overheat and fail. Always be sure the source voltage for your areas matches the required voltage for your amplifier. Diagram 6 Diagram 11 When connecting your speakers to the amplifier using spade connector; Unscrew the red and black caps on the binding post, be sure not to completely remove or unscrew the red and black caps.
Gain Controls – The gain controls are located on the front panel and are calibrated in 2dB of attenuation from full gain. The front panel provides four holes used to screw the unit into a rack.
Channel 1 Frequency Adjustment. The unit also provides a way to rear mount the unit into a rack for added security. Please do not return the amplifier to your dealer without contacting customer support. Service Hours are Monday through Friday 9: Low Cut Amfrican V and V Only – The low-cut filter removes extremely low frequencies from the audio signal that could cause speaker distortion or damage.
American Audio Stereo Amplifier V/V User Guide |
An ultrasonic network uncouples RF from the output and helps keep the amplifier stable with reactive loads. Always use the 50 Hz filter setting if you are using the amplifier to drive a distributed line system also known as a constant-voltage line, 70 volt line, etc. During signal overload, the limiter will reduce the input audio signal enough to minimize the amount ameriacn clipping.
The power-supply cord or the plug has been damaged. Dieses Symobl soll den Benutzer auf wichtige Instruktionen in der Bedienungsanleitung aufmerksam machen, die Handhabung und Wartung des Produkts betreffen. Turn channel two gain up. Antes de usar este amplificador, lea mas advertencias en la guia de operacion.
Um ddas Risiko eines elektrischen Schlages zu vermeiden, nicht die Abdeckung enfernen. Please read and understand this manual completely before attempting to operate your new amplifier. Connecting to the wrong voltage is dangerous and may damage the amplifier. At this point channel one will begin to distort.