Offering fast and affordable ASTM A Jominy End Quench Test of Hardenability along with heat treating and metallurgy expertise. This standard is issued under the fixed designation A ; the number 1 These test methods are under the jurisdiction of ASTM Committee A01 on. Steel. ASTM A Determining Hardenability of Steel – Designation: A – 99 An American National S.
|Published (Last):||15 March 2005|
|PDF File Size:||4.74 Mb|
|ePub File Size:||18.37 Mb|
|Price:||Free* [*Free Regsitration Required]|
The two test methods include the quantitative end-quench or Jominy Test and a method for calculating the hardenability of steel from the chemical composition based on the original work by M. A2555 Subsctiption a55 be the perfect solution. In the end-quench test the depth of hardening is the distance along the specimen from the quenched end a55 correlates to a given hardness level.
It is measured quantitatively, usually by noting the extent or depth of hardening of a standard size and shape of test specimen in a standardized quench. Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. It is astm a responsibility of the user of this standard astm a establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Distances for the odd number 1? Carbon multiplying factor 5 0.
You may delete a document from your Alert Profile at any time. Very light cuts with water cooling and a coarse, soft-grinding wheel are recommended to avoid heating the specimen. The water-supply line shall also be provided with a quick opening valve.
Your Alert Profile lists the documents that will be monitored. The Certified Material Satm Report shall state the method of sstm determination. An anvil providing a means of very accurately measuring the distance from the quenched end is essential.
Rockwell or Superficial Hardness.
ASTM A255 Jominy Hardenability Testing
The test consists of water quenching one end of a cylindrical test specimen 1. Plating and Coating Testing.
q255 Dry in air blast. It is measured quantitatively, usually by noting the extent or depth of hardening of a standard size and shape of test specimen in a standardized quench. For general statements regarding the use of test blocks and surface conditions, reference should be made to 4.
Hardness data is given in cert format with actual curve of material being tested. This standard has been a2255 for use by agencies of the Department of Defense. Add to Alert PDF. Repeat this procedure periodically, for example once a month, for each combination of? This standard is also available to be included in Standards Subscriptions.
Examples of this method are J 4? The support for the specimen shall be dry at the beginning of each test. The sample is then brought back up to austenitizing temperature as specified for alloy, and end quenched with a specialized holder for the end quench to occur.
When hardness readings are taken on two or more? Then make Rockwell hardness measurements on the C scale on the specimen as prescribed in 6.
ASTM A255 PDF DOWNLOAD
Historical Version s – view previous versions of standard. This standard does not purport to address aetm of the safety concerns, if any, associated with its use. For the example in The sample shall be held at the temperature listed in Table 1 for 1 h and cooled in air. The time between removal of the specimen from the furnace and the beginning of the quench should not be more than 5 s.
Active view current version of standard. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.
ASTM A PDF DOWNLOAD
The test consists of water quenching one end of a cylindrical test specimen 1. It is important that no vertical movement be allowed when the major load is applied. The Certified Material Test Report shall state the method of hardenability determination.
It is astm a quantitatively, usually by noting the extent or depth of hardening of a standard size and shape of test aetm in a standardized astm a Wash in hot water. For the example heat with 0.
For readings to 8? Immerse in solution No.
For simplicity, only multiplying factors for DI in inch—pound units are given. This testing can astm a done on a sub-sized sample which does not meet the standard size bar dimension as governed by Appendix X1.