ASTM D3654 PDF

ASTM D – Designation: D /D M – 06 Standard Test Methods for Shear Adhesion of. ASTM D/DM: Standard Test Methods for Shear Adhesion of Pressure- Sensitive Tapes. A summary of ASTM standards relating to pressure sensitive tape is attached. The shear test procedures are also harmonized: ASTM D and PSTC.

Author: Kazilabar Samushura
Country: Mexico
Language: English (Spanish)
Genre: Relationship
Published (Last): 4 November 2004
Pages: 350
PDF File Size: 15.35 Mb
ePub File Size: 15.37 Mb
ISBN: 970-7-95710-863-2
Downloads: 33142
Price: Free* [*Free Regsitration Required]
Uploader: Mikat

ASTM D Standard: Shear Adhesion Tester for Pressure Sensitive Tapes

If it is desirable to test slightly different widths for example, 25 of 50 mm of specimens per 8. France Stock lots. The roller shall move either mechanically or by hand at the rate of 10 6 0. Standards Subscriptions from ANSI provides a money-saving, multi-user solution for accessing standards. The surfaces of similar fiberboards may exhibit considerable variation between mills, between batches from one mill, and within batches.

Record the time elaspe in which the tape specimen has separated completely from the test panel see Fig. Only the sellers and buyers responsability is involved in case of dispute. The components of the variance for the following factors were estimated: The panel is mounted horizontally, tape side up, with the free end of the tape allowed to hang vertically over the rounded end.

Warning— All operations with solvents should be conducted in a wellventilated hood. Allow the remaining mm [8 in.

ASTM D3654/D3654M – 06(2011)

Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm. The resulting means and con? Proceed to Checkout Continue Shopping. Transport of foodstuffs or medical; warmth or cold Available in compartment simple, double or icebox typify Isothermal boxes icebox for two wheels, scooters, motorcycles typify A specimen size of 24 by 24 mm [1 by 1 in.

  DUODENO YEYUNO E ILEON PDF

The results are available. Need more than one copy? ASTM D The test plate with adhesive specimen is vertically hanged on the stand and its bottom is attached with a standard weight.

Please first verify your email before subscribing to alerts. This may be used to compare the shear adhesion of a tape to a particular fiberboard surface or to compare the shear adhesion of a tape to a variety of fiberboard surfaces.

Practice E is recommended. The lasting adhesive property could be obtained by measuring the displacement of specimen on vertical test plate or the time to failure at the load.

Wholesalers ads Partners Websites. The razor shall be held in position using side plates.

If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below.

Summary of Test Method 3. The radius of the curvature of the? Good cohesion is necessary for clean removal. International import and export trade leads board. The panel is mounted horizontally, tape side up, with the free end of the tape allowed to hang vertically over the round end of the panel. Between laboratories Between testers Between rolls Residual 0. To be suitable, materials must be lint free during use, absorbent, contain no additives that are soluble in the solvents listed in 6.

  INCIDER MAGAZINE PDF

Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. One company reports that, with care, the between laboratory standard deviation and the residual including within roll standard deviation may be higher or lower than reported here, depending on the tape type and manufacturer.

ASTM D | Rycobel

It may be desirable to mask the exposed adhesive of the free end of the specimen. The test plate with adhesive specimen is vertically hanged on the stand and its bottom is attached with a standard weight. The mass of the roller shall be 6 45 g [4. Link to Active This link will always route to the current Active version of the standard.

This may or may not relate to the ability of the tape to adhere to other surfaces. Your comments are invited aastm for revision of this standard or for additional standards and should be addressed to Asmt International Headquarters.

The width of the bar for 75 mm [3 in. As the voice of the U.

The tape must be at a true right angle to the bent

Author: admin