AWWA C950 PDF

AWWA C Fiberglass Pressure Pipe, Includes Errata (). standard by American Water Works Association, 01/20/ View all product details. ASTM D and AWWA C requirements. Strain Corrosion Testing. A unique and important performance requirement for GRP gravity pipe used in sewer. PIPE AWWA Cpdf – Download as PDF File .pdf) or read online.

Author: Nikoshakar Yozshuramar
Country: Denmark
Language: English (Spanish)
Genre: Literature
Published (Last): 28 February 2009
Pages: 341
PDF File Size: 17.3 Mb
ePub File Size: 6.23 Mb
ISBN: 318-7-13758-994-9
Downloads: 47002
Price: Free* [*Free Regsitration Required]
Uploader: Zuramar

The use of AWWA standards is entirely voluntary.

China Fiberglass Pipe Conforming to Awwa C Standard – China Fiberglass Pipe, GRP Pipe

They are determined in accordance with Sec. If these test results are not available, the value for Sb may be taken as the results of either of the following testing methods: Glass-fiber-reinforced epoxy RTRP epoxy.

Producers of goods made in conformity with an American National Standard are encouraged to state on their own responsibility in advertising and promotional materials or on tags or labels that the goods are produced in conformity with particular American National Standards. At deflection level B Table 9there shall be no structural damage as evidenced by interlaminar separation, separation of the liner or surface layer if incorporated from the structural wall, tensile failure of awws glass-fiber reinforcement, and fracture or buckling of the pipe wall.

This standard can be used as a guide for manufacturing this type of fiberglass pressure pipe. Cooling water GRP piping systems. Standards Subsctiption may be the perfect solution. The purchaser may also specify the following: Deflection levels for stiffness tests have been clarified Sec.

If a manufacturer desires to exclude inspection awws proprietary manufacturing processes, the manufacturer shall so advise the purchaser. Two methods can be used. This standard is not included in any packages.

AWWA publication of a standard does not constitute endorsement of any product or product type, nor does AWWA test, certify, or approve any product. The second edition was approved on June 23, A polymer containing two or more three-mem- bered rings, each consisting of one oxygen and two carbon atoms.

  MANUAL DO AZBOX BRAVISSIMO TWIN EM PORTUGUES PDF

A significant change is considered to occur when the average axial wwwa strength as determined in Sec. The Standards Council authorized the formation of the Standards Committee on Thermosetting Fiberglass Reinforced Plastic Pipe in Octoberand committee organization was completed in December Stiffness classes described are 9, 18, 36, and awqa psi 62, and kPa. Reinforced polymer—mortar pipe RPMP: Thus, users of this standard should consult the appropriate state or local agency having jurisdiction in order to 1.

A thin mat of fine c90 used primarily to produce a smooth surface on a reinforced plastic. Underground feeding GRP piping systems. Standards Subscriptions from ANSI provides a money-saving, multi-user solution for accessing standards.

The AWWA standards usually contain options that must be evaluated by awwwa user of the standard. This standard describes the fabrication and the testing of nominal 1-in through in mm through 4,mm fiberglass pipe and joining systems for use in both aboveground and belowground water systems.

Typical questions asked about products Does this product support customization? When plant inspection is awaa by the pur- chaser, the manufacturer shall provide the purchaser with adequate advance notice of when and where the production of ordered products will commence. Skip to main content. Acceptance in the foreword for additional guidance.

AWWA C950 SPECIFICATIONS FOR FIBERGLASS PRESSURE PIPE

Determine current information on product certification. Use of This Standard. Method 1 can be used for pipe sizes up to and including 27 in.

This standard is not included in any packages. In method 1, the pipe shall withstand, without failure, the c9550 loads listed in Table 12 when tested in accordance with the beam-strength test method of ASTM D Pipe joint capable of withstanding internal pressure and longitudinal tensile loads.

  BIOERODIBLE POLYMERS PDF

Determine additives requirements, including applicable standards. Each of the two samples shall conform to the requirements specified. The end of a pipe test specimen with an end closure configura- tion such that internal pressure produces longitudinal stresses in addition to hoop and radial stresses in the pipe test specimen.

Click here to sign up. The manufacturer shall perform hoop tensile strength tests at a frequency of one test for each lengths of pipe produced or from each manufacturing run, whichever provides the most frequent sampling of each class and size.

The composite structure may contain aggregate, granular or platelet fillers, thixotropic agents, and pigments or dyes. A filled or unfilled resin layer, nonreinforced or reinforced, that is applied to the exterior surface of the pipe structural wall. Si shall be taken as the 95 percent lower-confidence level, back extrapolated to 0. The permissible adhesive-bonded joints are as follows: Combining the strength of GRP FRP and the chemical compatibility of plastics provides customers awwx a superior alternative to costly metal alloys and rubber-lined steel.

Pipe diameters and tolerances shall be as shown in Tables 1, 2, 3, 4, 5, and 6 when measured in accordance awwq ASTM D A separate external device or structure that is assembled or constructed around a joint to provide restraint to longitudinal tensile forces. Service and distribution piping systems and transmission piping systems are included. We have no amendments or corrections for this standard.

Pipe joints capable of withstanding internal pressure and longitudinal tensile loads. Specific service and installation considerations. Total quantity of jointing materials and field allowances. Auxiliary GRP piping systems. The third edition was approved on Jan.

Author: admin