BC558 TRANSISTOR DATASHEET PDF

DataSheet: PDF icon BCPDF. BC is a general purpose PNP transistor. It is used in switching and amplifier applications. The DC current gain varies in. BC Transistor Datasheet pdf, BC Equivalent. Parameters and Characteristics. Semiconductor data sheets and/or specifications can and do vary in different applications . BC / BC / BC VCE = -5 V, IC = µA.

Author: Meztilmaran Faenris
Country: Egypt
Language: English (Spanish)
Genre: Art
Published (Last): 28 December 2008
Pages: 160
PDF File Size: 4.99 Mb
ePub File Size: 13.52 Mb
ISBN: 838-9-63575-240-5
Downloads: 52538
Price: Free* [*Free Regsitration Required]
Uploader: Zukus

When a transistor is used as a switch it is operated in the Saturation and Cut-Off Region as explained above.

The DC current gain varies in range to Where an input signal of low voltage is amplified switched to high voltages t0 drive loads like speakers. BC is a PNP transistor hence the collector and emitter will be closed Forward biased when the base pin is held at ground and will be opened Yransistor biased when a signal is provided to base dagasheet.

Interface SD Card with Arduino. Choosing Motor For Robots. It is also used as a complement for transistors BC to BC Arduino based GPS ttansistor.

HTTP This page has been moved

Submitted by admin on 26 March For amplification applications, the transistor is biased such that it is partly on for all input conditions. In the absence of base signal, it gets completely off. BC has a gain value of to ; datsheet value determines the amplification capacity of the transistor.

  6ES7 350-2AH00-0AE0 PDF

Interface GPS with Arduino.

For switching applications, transistor is biased so that it remains fully on if there is a signal at its base.

The input signal at base is amplified and taken at the emitter.

SPI Module of Arduino. Amplifier modules like Audio amplifiers, signal Amplifier etc.

BC Pinout, Configuration, Circuit As Switch & Amplifier

BC as switch When a transistor is used as a switch it is operated in the Saturation and Cut-Off Region as explained above. Transixtor to main content. The voltage divider is the commonly used biasing mode. Of the above types common emitter type which amplifies voltage is the popular and mostly used configuration.

A Transistors acts as an Amplifier when operating in Active Region. Also note that a PNP transistor is always used for high side switching, meaning the collector is connected to power and emitter to load that is to be switched.

When this transistor is fully biased then it can allow continues current of mA to flow across the collector and emitter.

Virgin Galactic transjstor Commercial Space Flight. Complete Technical Details transitor be found in the BC datasheet given at the end of this page. This high-density System-in-Package SiP integrates controller, power switches, and support components.

It is used in switching and amplifier applications. When uses as an Amplifier the DC current gain of the Transistor can be calculated by using the below formulae. BC is a general purpose PNP transistor. It can amplify power, voltage and current at different configurations. This is known as the biasing.

  ART SOBCZAK SMART CALLING PDF

BC558 Datasheet, Equivalent, Cross Reference Search

The transistor terminals require a fixed DC voltage to operate in the desired region of its characteristic curves. The BC because of this large gain value is normally used to as a audio amplifier. As discussed a transistor will act as an Open switch during Forward Bias and as a closed switch during Transisttor Bias, this biasing can be achieved by supplying the required amount of current to the base pin.

A resistor is always added in series with base pin to limit the base current.

When base current is removed the transistor becomes fully off, eatasheet stage is called as the Cut-off Region and the Base Emitter voltage could be around mV. What is Web Browser.

In the below GIF you can notice the transistor being switched for a low voltage 1v audio signal. TL — Programmable Reference Voltage.

Transistor BC558

BC is used in common emitter configuration for amplifiers. The value of this resistor RB can be calculated using below formulae. Choosing Battery for Robots.

Author: admin