CFGQ Silicon Labs 8-bit Microcontrollers – MCU 25 MHz 16 kB 8- bit MCU datasheet, inventory, & pricing. Explore the latest datasheets, compare past datasheet revisions, and confirm part lifecycle. CF datasheet, CF pdf, CF data sheet, datasheet, data sheet, pdf, Silicon Laboratories, Full Speed USB, 16k ISP FLASH MCU Family.

Author: Kajijind Kenos
Country: Turks & Caicos Islands
Language: English (Spanish)
Genre: Life
Published (Last): 12 August 2005
Pages: 466
PDF File Size: 15.95 Mb
ePub File Size: 17.21 Mb
ISBN: 252-1-61584-936-7
Downloads: 43501
Price: Free* [*Free Regsitration Required]
Uploader: JoJot

The daughter card is pre-loaded with datashewt game that requires you to mimic LED light sequences by entering the sequence via the capacitive touch sense pads.

Refer to the datasheet section associated with a particular on-chip peripheral for information regarding valid interrupt conditions for the peripheral and the behavior of its interrupt-pending flag s. C2 Interface Figure EP2 is 64B whether or not double-buffered.

Silicon Labs 電容觸控式相關應用

Datasheet of the following may be selected as the positive input: Endpoint 0 interrupt inactive. The capacitor should be no greater than pF; however for very small capacitors, the total capacitance may be dominated by parasitic capacitance in the PCB layout.

The traces should be as short as possible and shielded with ground plane from any other traces which could introduce noise or interference. Note that parameters which affect ADC measurement, in particular the voltage reference value, will also affect temperature measurement. Stack Overflow works best with JavaScript enabled.



datssheet If enabled, the Missing Clock Detector will cause an internal reset and thereby terminate the Stop mode. Typical C2 Pin Sharing The selected device should be configured according to Equation IN Endpoint Double-buffer Enable.

Seems very cool though, it having a temperature sensor in the ic, full USB with no external clocks, and that is a very beefy regulator! Second, the configurable sensitivity makes the switches easy to use with a variety of materials covering dahasheet PCB, such as plexiglass, glass, or various plastics.

This bit selects the source for the internal voltage reference.

MHz, disabling the Flash one-shot will increase system power consumption. If there is new information available in the receive buffer that has not been read, this bit will return to logic 0.


Dwtasheet Falling-Edge Interrupt Enable. External RC Example network is used as an external oscillator source for the MCU, the circuit should be configured as shown in Figure Why does the report fill time need to be longer than bInterval?

Enhanced Baud Rate Generation These bits select which Port pin is used as the Comparator1 positive input. The bit rate when operating as a master will never exceed the limits defined by equation Equation The sensitivity of the switches is also easily configurable in firmware which enables two useful features.


Comparator0 is shown in Figure 7.

(PDF) C8051F320 Datasheet download

Comparator0 rising-edge interrupt disabled. This bit sets the priority of the SPI0 interrupt. Used by SJMP and all conditional jumps. A total of eight endpoint pipes are available: Turbo J 6, 1 17 Once cleared to logic 0, a Flash bit must be erased to set it back to logic 1. The lower bytes of data memory are used for general purpose registers and scratch pad memory.

USB Reset Flag 0: I have EP1 as 64B when not double-buffered and 32B when double-buffered. Timer 3 interrupts set to low priority level. Comparator0 rising-edge interrupt enabled. Writing a byte to SBUF0 initiates the transmission. Crystal oscillator circuits are quite sensitive to PCB layout. This was also my first Home-etched double sided board, a total failure, ratasheet and button sides seemed perfectly aligned, but a few mills off ruined some pads and traces where holes where drilled.

P About the libraries, if they are good then I don’t really see much of a shame in using them.

Author: admin