All OMRON products are capitalized in this manual. The word .. purpose and a comparison between the CQM1H and the CQM1. Section 2. 1. V4+. Voltage pin, input 4. 2. V Common pin, input 4. 3. V3+. Voltage pin, input 3. 4. V Common pin, input 3. 5. V2+. Voltage pin, input 2. 6. V Common . View and Download Omron CQM1 operation manual online. Programmable Controllers. CQM1 Controller pdf manual download. Also for: Sysmac cqm1.

Author: Mira Nisho
Country: Portugal
Language: English (Spanish)
Genre: Relationship
Published (Last): 6 August 2004
Pages: 139
PDF File Size: 11.3 Mb
ePub File Size: 10.56 Mb
ISBN: 445-7-89069-281-2
Downloads: 22307
Price: Free* [*Free Regsitration Required]
Uploader: Mikakazahn

Page 10 Application Precautions overall machine to fail to meet the Standard. Do not tighten any screw of the terminals to a torque exceeding 0. Glossary Programmable Controller A computerized device that cqmm1 accept inputs from external devices and gener- ate outputs to external devices according to a program held in memory.

Page Bits 11 to 14 of the output data have nothing to do with output current i. Use either of the following types of M3 solderless terminals for the input lines connecting to the terminals. Page Analog Input Unit Move the object to the position where you want to turn ON the output cmq1 press the teaching button. Connector Type Dimensions when Mounted mm Approx.

Programming and Adjustment 3. Total cable length per system: Be sure that the operating environment is within the specified condi- tions at installation and remains within the specified conditions during the life of the system.

You must read this section and understand manuxl information contained before attempting to set up or operate a PC system. This terminal is used if the Unit is set to any timing hold other than normal.


OMRON CQM1 Operation Manual

Page On the other hand, the SCL instruction cannot process negative values. Page Glossary link A hardware or software connection formed between two Units. In this case make sure that the optical fiber cable of the sen- sor is connected securely and that there is no sensing object, and then repeat from step 3.

Manjal Ready indicator green, lit when the Unit is rec- Word number indicator orange, lit janual two words are ognized as the Temperature Control Unit used and not lit when a single word is used Terminal screws: Programming Console Operation Errors. Reflective model If the shielded parallel cable with vinyl insula- Shielded parallel cable with vinyl tion is not available, use two single-conductor E3C-DS10 insulation shielded vinyl cables. Take the following steps to set the input word to BBBB.

For nj-series cpu unit. The following methods represent typical methods for reducing noise, and may not be sufficient in all cases.


Dqm1 single-unit Programmable Controllers are available, building-block Programmable Controllers are constructed from separate components.

Refer to page for details. In the same manner, the X2 manial can be set as the largest object input value if the scaling command is executed while the largest object is being sampled. The current manipulated variable will be monitored.

Page Programming Console Operations Section 3. Caution Expansion instructions those assigned to function codes 17, 18, 19, 47, 48, 60 to 69, 87, 88, and 89 are not subject to program checks.


If a Programming Devices is involved, the Programming Device is considered the host computer. Note If power is not turned on for at least one minute before replacing the An operation control command must be executed to start actual opera- tion. The Appendices provide the vqm1, block diagram, data processing timing, and troubleshoot- ing for the Units. Press the CHG Key to begin 3-word data modification.

Omron CQM1 Operation Manual

Page 43 Section Wiring 4. Words in the DM area cannot be accessed bit by bit. Not lit when set to 16IN.

If the command code is correct, a set value will be manuual to the input word corresponding to the command as the manuwl for the com- mand. If the instruction has more operands, the operands will be deleted automati- cally with the instruction. The memory area used to hold the active program, i. Chapters Table Of Contents The information contained in this section is important for the safe and reliable application of the Programmable Con- troller. Functions Forced Zero Zero-shift Sensors can be mounted together in parallel, however, if their cable length switches are set to different values.

Set Value Teach This command can be used only when the timing hold in operation mode A is set to normal.

Author: admin