DIN 24342 PDF

LOGIC CARTRIDGE VALVE – DIN 1/3. L09 03/ Type. Size. Max pressure. Area ratio. ICLI DN bar. 1: 1: 1: 1: /S. ICLI ARON cartridge valves are basi- cally composed of a cover and an operating unit insert in the ISO (DIN ) mounting frame. Each cartridge valve is. (). (). (). (). (). () () () () () (). * only together with d4 max and t4 max. Installation Dimension as per DIN

Author: Mikalrajas Doum
Country: Swaziland
Language: English (Spanish)
Genre: History
Published (Last): 24 February 2012
Pages: 450
PDF File Size: 13.17 Mb
ePub File Size: 9.78 Mb
ISBN: 727-3-12983-731-9
Downloads: 5994
Price: Free* [*Free Regsitration Required]
Uploader: Mazuzragore

Do not apply Loctite or equivalent to the orifice plug.

CVIHFV Configuration | Eaton PowerSource

Cartridge Valves mounted in a manifold block provide a compact, integrated circuit for simplified machine design and reduced system costs. Spool valves must be sized for the maximum flow seen at any of their ports. All Vickers valves undergo full fatigue and endurance tests before release.

Amplifier Designed for zero leakage when closed. Cartridge relief valves feature manual pressure setting adjustment. Z2 X Alternatively, for system pressures up to bar psi max. Cable entry 6,0 0. Please consult your Vickers representative before ordering.

Slip-In Cartridge valve, ISO (DIN )

B In Figure 51 the system is vented when the solenoid of the pilot valve is de-energized; when the solenoid is energized the system pressure is limited to the setting of the CVGCA-3 module. Pilot port Y maximum pressure limit is also bar psi. All warranties shall expire 12 months from the date the article is placed in service, or 24 months from the date the article is supplied, whichever is the earlier.

  AMANDO A PABLO ODIANDO A ESCOBAR DESCARGAR GRATIS PDF

See page for sizes of factory-fitted standard orifices. Non-standard orifice requirements should be defined as follows: Additionally, venting and remote piloting are possible. Installation metric threads for orifices dimensions unchanged for design S – SAE threads for closure plugs; numbers 10 to 19 inclusive.

For response data of dynamic models type ZD Nsee page The Y port is used to drain the pilot oil. The dynamic insert can only be used with the special dynamic cover.

NG 16 – NG D poppets cannot be used for flow from B to A. Fully interchangeable with conventional cartridges.

LOGIC ELEMENTS ISO 7368 (DIN 24342)

Dynamic range is available in sizes 16 to Higher pressure drops result in improved control. Cracking pressure, bar psi For models ZD L – 1,0 The calculation provides a starting point for determining the right orifice for the application.

The final determination is the application itself, and fine tuning should be done on the machine installation. If pressure compensation is added to the pilot stage, the complete valve is pressure compensated. Sizes 25, 32, 40 Area ratios are defined as 1: CVGS 224342 These six modules were designed to satisfy the needs of Vickers application and systems engineers in providing effective solutions to a wide variety of pilot control requirements in cartridge valve systems.

  DAVIDSON ANOMALOUS MONISM PDF

By changing orifice sizes or adding or deleting them, dni cartridge can be fine tuned diin achieve desired machine operation. The model identification for size 05 pilot valve interface options is: These cartridge valves are integral assemblies of cover and insert with a main spool that is fully seated in its closed position.

Cartridge Valves Slip-in Cartridge Valves to ISO 7368 (DIN 24342) Vickers

Low hysteresis, fast response option: Sizing of control orifices is key to tuning the relative response of each cartridge unit. This allows free flow from insert port A to port B while blocking flow from B to A. The model identification for size 03 pilot valve interface options is: Other orifice sizes can be fitted by special arrangement with your Vickers representative. Minimum pressure is 0,3 to 5 bar 4. The inserts have an area ratio of 1: P A B P T B A X Z1 Excepting pressure reducing and unloader cartridge inserts, which have spool type construction, inserts are designed with a positive-seating poppet mechanism.

Cracking pressure, bar psi L – 0,3 4. Tapped port for installation of additional orifices.

For flow A-B, poppet drilled from A. The A insert stroke adjuster cover is available with three types of adjusters, micrometer Mmicrometer with keylock K or standard square 2342 screw with hex.

Author: admin