EUROMAP 70 Electrical Interface between Injection Moulding Views. 6 years ago. Euromap, · Electrical, · Interface, · Injection, · Moulding. Euromap 2: Mould Fixing Dimension for Injection Moulding Machines. Specific information .. Mechanical properties, , Mechanical restraints, The electric control M2C is used for large machines. – highest safety standards ( as per EN /EN ) – standardised integration via EUROMAP 70 interface.
|Published (Last):||2 November 2009|
|PDF File Size:||11.67 Mb|
|ePub File Size:||13.79 Mb|
|Price:||Free* [*Free Regsitration Required]|
Products Service Support Downloads Company. Functional principle and interface of the magnetic clamping system: M-TECS function principle for horizontal design. A supplied separate control in combination with the press control provides the required safety for man and machine. All signals except table 1: Also very small moulds are safely clamped.
The technology of the magnetic clamping plates is based on the principle of an electro-permanent magnet and is thus safe, even in case of a pressure failure. The forces can be adapted upwards and downwards to the needs of the machine. Unless otherwise noted, the switch contacts are switching the reference potential plug euro,ap A further supplier added v. Magnetic clamping systems especially designed for mould carrier machines.
Quick die change on presses and automatic punching machines.
Combinations with Hilma machine vices or Stark zero point clamping systems can be easily realised, as they all come from a single supplier.
Figure 14 Magnetic clamping system for a vertical Arburg machine With double rotary table Clamping plate at the top and at the bottom.
M-TECS function principle for vertical design. Exact positioning on the machine table is ensured using 20H7 longitudinal and crosswise slots.
The mains supply of the MCS is also specified. Pin a2 and Table 2: The magnetic clamping systems or clamping plates have been especially designed for injection moulding machines, rubber presses, die casting machines, mould carrier and presses for metal forming.
Plug on the injection moulding machine male. Figure 13 Magnetic clamping systems for an injection moulding machine of the company Krauss Maffei Closure force: The system itself does not have any movable elements and is practically maintenance-free. Pin d2 18 — 36V DC max. Only to unclamp the die, electrical energy is required again. Rotary table with magnetic plate.
Figure 11 Magnetic clamping systems for an injection moulding machine of the company Krauss Maffei Closure force: The interface to the press is always designed redundantly, is effected via potential-free contacts to stop or drive the machine. Figure 8 Magnet clamping system for an injection moulding machine of the company Engel Closure force: For the injection moulding machine see Figure 2 and the magnetic clamping system see Figure 1 the plug contacts should be capable of taking a minimum of V and 10 A.
In addition recommendations are given for signal voltage and current levels.
Magnetic clamping systems for deformation tools | Römheld GmbH Friedrichshütte
Die or mould change on punches and presses within a few minutes as well as further processing advantages are created with Hilma magnetic clamping systems. Control and signal exchange with requirements for high performance levels. Figure 9 Long pole technology in a to injection moulding machine Closure force: Safety of the magnetic clamping system: The contact making is either potential-free or related to a reference potential supplied to a contact of the plug mounted on the injection moulding machine or the magnetic clamping system see Tables 1 and 2.
Inquiry – checklist for a quotation: Figure 10 Magnetic clamping system installed in Arburg C High concentration effect of the magnetic force close to the centring ring. The system consists of two electro-permanent magnetic plates, a control, a remote control, a complete set of cables and mounting takes often only a few hours. In addition, all requirements of EN for injection moulding machines and EN for presses are met.
M-TECS square poles for extremely heavy machining Each magnetic plate can be individually adapted to the particular machine table.
Additional T-slots, mounting holes, stops and special dimensions are not a problem to us. This penetrates only a few millimetres into the die base plate and will therefore have no impact on the die and the products. During the whole machining process, the control continuously monitors the parameters of the magnetic force, the position of the die die contact and the temperature. All signals which are not optional shall be supported by all injection moulding machines and magnetic clamping systems.
Plug on the injection moulding machine female. Figures 1 and 2 corrected v. The signals are conducted from the signal source to the respective pin.
The product range “M-TECS” stands for magnetic clamping technology, that means clamping technology of the highest level and offers the following key advantages for the user: It is suitable for fitting or retrofitting without any problems in nearly all presses. Figure 7 Magnetic clamping system in a rubber moulding press of the company PanStone Plate size xmm, magnetic force kN realised for small and medium mould weights. The mould halves are heated by the magnetic heating plate.
The design euromwp the magnetic plates is very flexible and can be adapted in size and shape for different eurompa according to the user’s specification.
EUROMAP 70 – version 1.5
There are no limits set to the geometric shape of the magnetic plates. The magnetic force is generated in a very flat, highly concentrated magnetic field. Clamping forces of e. For easy and safe eurommap change, roller bars with spring packs are installed below the magnetic plate.