· · · · · · · · · The Hantarex Polo. (25″ model displayed). Resources: Manual: http://arcarc. % I won a golden tee golf machine off ebay for spares or repairs. The fault was no display so i guest.
|Published (Last):||25 September 2016|
|PDF File Size:||19.56 Mb|
|ePub File Size:||20.28 Mb|
|Price:||Free* [*Free Regsitration Required]|
Please consider making an end-of-year donation to the International Arcade Museum Library and locking in your donor badge if you haven’t already. The fault was no display so i guest it was the monitor.
The lopt you need is a HR or Eldor That’s just a standard Polo 1 25″ 15khz chassis, nothing fancy! I assumed you’d checked that already but obviously you want to get that changed out for a new one hantarrx you go any further!
I’ve just used it to recap my monitor and it worked a treat The first time you switch the machine on all is ok. Thanks to tb for the parts to repair my chassis.
Hantarex Polo 25″ capacitor list/map and recap log – Arcade Otaku – アーケード オタク
Turn it very slowly until you reach V. I could not find them on the CCT from the manual. It works OK for now as far as I can see? Chemicon SME series C 22uf 50v originally fitted: Every donation is appreciated, big and small.
Originally Posted by Sluggy Not all polo2’s are dual! Iv been readin about cap kits ect would this fix it?
Hantarex Polo 25 / 28 Arcade Monitor Cap Kit
Send a private message to john Daewoo RS series C 10uf 63v originally fitted: I thought maybe that was how to switch from 15K 25K. The cage has tabs that stick through holes in the chassis and are rotated to lock the cage on. I did a continuity check on TH and it was the same as before. Hantarex Polo tips and tricks: I see no reason not to spend some eur more and get Nichicon ones for example instead of the LeLons I can get locally.
You should be getting v or thereabouts. It was very confusing cause I checked the neckboard over about times and found nothing wrong with the neck socket or R C is in fact C Sometimes the top will be stretched, and the bottom squished, and vice versa.
If it’s not that, there may be damage to the connector on the monitor. Starting with the middle heatsink, there are two ICs: This may use a little bit hantarxe finesse to get off, but it just pulls off.
If not, get you mutlimeter, set it to volts DC range and put you red probe in the yoke plug, the black probe on the lopt heatshield. As noted above, these seem to fail a lot, probably from the increased ambient heat from hantadex cage being installed.
Below is a pic from the back of the cab. C is 22uF 50V. Something else unusual happened to this chassis.
Finished the recap and everything works as expected, no more screen size change when stuff happens in games Also pictured is a PSU I also recapped. Daewoo RSS series C3 10uf 63v originally fitted: You can see plain as day how many cracks there were in the flyback area. Also on a related topic, is there a place that explains the general guidelines when adjusting color values? On the outer hantardx of the chassis behind the HOT heatsink are two ceramic resistors.
Organized Mass Confusion » Blog Archive » Hantarex Polo Tips and Tricks
Edited by tb – 19 Jan at You don’t need to do any kind of continuity check on a lopt that’s in that bantarex of condition – no lopt should be burnt and have goo coming out! After about 10 minutes is starts to lose vertical hold. As I noted, the wall heatsink has the voltage regulator mounted to it.
Underneath you can oplo that I had to patch about 7 traces. The cage should come right off then.
HANTAREX POLO 25
Im running games with a vga to tv converter on my Shangai Novel, with composite and it looks amazing, Im not interested in RGB or Scart.
Daewoo RSS series C 1uf v originally fitted: Originally Posted by Sluggy. The time now is I am making this thread to document the process of recapping an EU Hantarex POLO 25″ monitorI decided to do that because after searching I only found partial info on the capacitors neededor scattered info buried in threads or cap kits that are missing capacitors This black jumper wire is a very handy feature, as it will prevent the monitor from powering on with the yoke unplugged running any monitor with the yoke connections not plugged in can potentially damage the chassis.
I then looked at the board and found two resistors burnt R and R