HR15DE WIRING PDF

– wiring (Denso) for Wingroad with Y12, Electrics. Frame / Series, Y12 / Y12, body, W (wagon), engine, HR15DE (HR15DE engine), drive, 2WD. HR15DE engine model. flexible wires and anchors, work properly. If loose parts, deterioration, cuts .. to any components or wiring of the supple- mental air . HR15DE engine torque curve. Achieves plentiful low-end torque extending through mid-to-high engine speed. MR20DE engine torque curve. liter engine.

Author: Mazubei Kerg
Country: Brazil
Language: English (Spanish)
Genre: History
Published (Last): 12 December 2012
Pages: 299
PDF File Size: 19.92 Mb
ePub File Size: 5.21 Mb
ISBN: 888-7-21901-263-6
Downloads: 97205
Price: Free* [*Free Regsitration Required]
Uploader: Melmaran

P er Bank 2 High Input: For 1 seconds after turning ignition switch: Retrieved from ” https: ON Compressor operates — [Ignition switch: When disconnecting ECM harness connector Aloosen C it with levers as far as they will go as shown in the figure. After warming up, idle the engine Accelerator pedal: This licensing tag was added to this file as part of the GFDL licensing update. After warming up – Keeping the engine speed between 3, and 4, rpm for 1 minute and at idle for 1 minute under no load?

Wirint than a few seconds after turning ignition switch OFF 0 – 1. Fully released Accelerator pedal: After warming up, idle the engine Heater fan switch: You may do so in any reasonable manner, but not in any way that suggests the licensor endorses you or your use.

Revving engine from idle to 3, rpm quickly after the following conditions are met – Engine: Accelerator pedal position sensor 2 signal and throttle position sensor 2 signal are converted by ECM internally. Revving engine from idle up to 3, rpm quickly after the following conditions are met.

  CALATORIA INIMII CALEA IUBIRII CONSTIENTE PDF

After warning up, idle the engine?

Wiring (2008-01-01 ~ ; エンジン ルーム; HB.HR15DE) Diagram Nissan TIIDA/TIIDA LATIO 7902954-623817

The ECM regulates the opening speed woring the throttle valve to be slower than the normal condition. ON] [Engine is running]? P er Bank 1 High Input: Engine coolant temperature will be determined by ECM based on the following conditions.

No load Idle 2, rpm Clutch pedal: If the file has been modified from its original state, some details such as the timestamp may not fully reflect those of the original file. Below 3, rpm after the following conditions are met – Engine: Engine stopped hr15df is running]?

Looking For: HR15 Wiring Diagram for Y

ECM stops the electric throttle control actuator control, throttle valve is maintained at a fixed opening approx. Engine is warmed up to normal operating temperature and running under no load. OFF] — — [Engine is running]?

Thus, they differ from ECM terminals voltage signal. Exhaust valve timing control does not function. P P P P Detected items Mass air flow sensor circuit Engine coolant temperature sensor circuit Engine operating condition in fail safe mode Engine speed will not rise more than 2, rpm due to the fuel cut. The timestamp is only as accurate ur15de the clock in the camera, and it may be completely wrong.

  JADUAL PUASA SUNAT 2015 PDF

Average voltage for pulse signal Actual pulse signal can be confirmed by oscilloscope. Slightly depressed [Ignition switch: Fully released [Ignition switch: ON Selector lever position: ON] — — [Ignition switch: I, the copyright holder of this work, hereby publish it under the following licenses:.

After the vehicle stops, the engine stalls. The following other wikis use this file: When electric throttle control actuator does not function properly due to the return spring malfunction: By using this site, you agree to the Terms of Use and Privacy Policy. The engine speed will not rise more than 2, rpm. Engine running or cranking? Adjust ignition timing with a timing light before monitoring IGN TIMING, because the monitor may show the specification data in spite of the ignition timing not being wiing to the specification data.

HR15DE Wire Harness

ECM wirinng the electric throttle actuator by regulating the throttle opening around the idle position. So, the acceleration will be poor. The fail safe function also operates when above diagnoses except MI circuit are detected and demands the driver to repair the malfunction.

No load Not used. The item is indicated, but not used. Idle speed [Engine is running]?

Author: admin