IC CD4013 PDF

The CD dual D flip-flop is a monolithic complementary MOS (CMOS) integrated circuit constructed with N- and P-channel enhancement mode transistors. dual D-type flip-flop is a monolithic complementary MOS (CMOS) integrated circuit constructed with N- and P- channel [ ]. CMOS Dual ‘D’-Type Flip-Flop. Consists of two identical, independent data-type flip-flops. Each flip-flop has independent data, set, reset, and clock inputs and Q.

Author: Vilmaran Nikus
Country: Burundi
Language: English (Spanish)
Genre: Technology
Published (Last): 19 June 2006
Pages: 238
PDF File Size: 19.93 Mb
ePub File Size: 18.26 Mb
ISBN: 303-5-46427-439-6
Downloads: 96488
Price: Free* [*Free Regsitration Required]
Uploader: Mauran

Latest posts by Frank Donald see all. The circuit above can be a best solution for those who want to build an effective and low cost Electronic lock. The configurations can be repeated by connecting the modules in series for getting the time period to any desired lengths, but in multiples of two.

They can be used in toggle circuits. The signals produces a bistable effect over one of the free outputs, the cd40013 being connected to the Data input as explained above. The signal may be applied externally through a transistor astable multivibrator or more conventional types using NAND gates or NOR gates. All flip flops do the same thing- they store a value if the output s indefinitely unless the value is intentionally changed by manipulating the inputs.

The set up shown can be simply built with the help of the diagram. This is only case when the Q and Q outputs are the same value.

  DYSON DC21 MANUAL PDF

Understanding IC 4013 Pin-Outs and Specifications – Datasheet and Application Circuits Explained

If the set pin is 0 and the reset pin is 1 D is Xthen the Q output is 0 and xd4013 Q output is 1. This input is used for receiving clock signals which are normally in the form of square waves.

In this circuit, when one LED is on, the other is off.

B will gives a low signal which in turn turns the PNP transistor ON and therefore the relay gets activated. The executes instructions on the rising edge of a clock signal.

These inputs change the values of the output pins, Q and Qaccording to the D flip flop truth table that is shown above. It outputs a data value of either 0 or 1 from the flip flop.

If the set pin is 1 and the reset pin is 1 D is Xthen the Q output and the Q output are both 1.

The can actually take a wide range of voltage, anywhere from 3VV. Positive input Pin X on the truth table means that the value of that pin doesn’t matter.

A D flip flop is just a type of flip flop that changes output values according to the input at 3 pins: So initially all the pins have a value of 0 cd4031 when we push down on the pushbutton, it then has a value of 1.

We connect a clock signal to the clock of thewhich is pin 3. So, in this circuit, this is the only time when both LEDs will be on.

  JOHANN MATTHESON PDF

Notify of all new follow-up comments Notify of new replies to all my comments. It means it doesn’t matter what logic state the data input is in. Video games, blogging and programming are the things he loves most. Below is the truth table for the D flip flop pulled from the datasheet of the chip. The sets of outputs change states when operated in the bistable mode or while setting and resetting the IC, always producing opposite logic levels at any instant.

IC, CD, Dual D Flip-Flop

The operation of a single D cd40013 Flip flop unit is very important to understand the working principle of the above circuit. The clock pin is the pin where we feed a clock signal.

Pin 5 is the data pin. The components used in this circuit is very common and you can purchase it in any local electronics store or try it via online. So, for example, the green LED can mean the circuit is on or running and the red LED can mean the circuit is off or not running. By using pushbuttons to control the inputs, you can see exactly how the flip flop reacts to changes in inputs. To the Q output pin, we connect a green LED. Flips are used in memory devices.

Author: admin