IPMP CONFIGURATION SOLARIS 10 PDF

Oracle Solaris Administration: IP Services Oracle Solaris 10 1/13 Information An IPMP configuration typically consists of two or more physical interfaces on the . For IPMP configuration tasks, refer to Chapter 31, Administering IPMP (Tasks). Oracle Solaris IPMP involves the following software: You can configure one of the interfaces down to 10 megabits and still place the two interfaces into the. You must have configured all interfaces as members of the IPMP group. role to a user, see Chapter 2, Working With the Solaris Management Console (Tasks).

Author: Faugor Akinogis
Country: Lithuania
Language: English (Spanish)
Genre: Finance
Published (Last): 3 August 2004
Pages: 75
PDF File Size: 10.91 Mb
ePub File Size: 10.88 Mb
ISBN: 281-5-35229-307-5
Downloads: 26019
Price: Free* [*Free Regsitration Required]
Uploader: Kagajora

How to configure Solaris 10 Link Based IPMP

Additionally, any existing connections to the system using those IP addresses are disrupted. For example, to place hme0 and hme1 under group testgroup1you would type the following commands:.

To ensure that each interface in the IPMP comfiguration functions properly, in. Assign the standby interface to the same IPMP group, and configure a test address for the standby interface.

When the hme0 interface fails, notice that all data addresses move from hme0 to hme1. Internet Key Exchange Overview.

To turn on the failover attribute of the address, you lpmp use the failover option without the dash All test IP addresses in an IPMP group must use the same network prefix. Fist i am going to disable eg1 and let see what happens.

On the system with the interfaces to be configured, solarix the Primary Administrator role, or become superuser. Configure the interface with a test address Repair detection is the process of detecting when a NIC or the path from a NIC to an Internet layer device starts operating correctly after a failure.

These network interface drivers monitor the interface’s link state and notify the networking subsystem when that link state changes. Note — You can always view the current status of an interface by typing the ifconfig interface command. However, if you must remove the system component, you can confoguration this behavior by using the -f option of cfgadmas explained in the cfgadm 1M man page.

  EL SECRETO DE LAS RUNAS GUIDO VON LIST PDF

How to configure Solaris 10 IPMP ? – UnixArena

Configure an interface as a standby and assign the test address. Load spreading solarjs only when the network traffic is flowing to multiple destinations that confivuration multiple connections. The same non-null character string IPMP group name identifies all interfaces in the group. After the daemon receives 10 consecutive replies for a default repair detection time of 20 seconds, solariss daemon determines that the interface is repaired.

Preventing Applications From Using Test Addresses After you have configured a test address, you need to ensure that this address is not used ipnp applications.

Your email address will not be published. Depending on your failure detection requirements, you might need to either use specific types of network interfaces or configure additional IP addresses on each network interface. The physical interface in an IPMP group is not present at system boot.

IPMP also provides load spreading of packets for systems with multiple interfaces. Specific information about DR in the Sun Cluster environment. For an introduction to test addresses, refer to Test Addresses. Link-based failure detection is always enabled, provided that the interface supports this type of failure detection.

IPMP Configuration – Solaris 10 vs Solaris 11

You can add new interfaces to an existing group on a live confituration. Detaching NICs All requests to detach system components that contain NICs are first checked to ensure that connectivity can be preserved. This message indicates that interface hme0 was added solqris IPMP group testgroup1. For example, to create an IPv6 test address, you would type the following command: Troubleshooting Network Problems Tasks.

Repair detection assumes that you have enabled failbacks. Similarly, if you configure as standby an interface that already has data addresses, these addresses automatically fail over to another interface in the IPMP group. You can remove the component from the system.

  FALLOUT PNP CHARACTER SHEET PDF

Rammeesh unix: IPMP in Solaris 10

The Primary Administrator role includes the Primary Administrator profile. Routers that are connected to the IP link are automatically selected as targets for probing. This process is called load spreading.

You use IPMP options of the ifconfig command to create the configuration. Test addresses are IPMP-specific addresses that are used by the in. No test address configured on interface hme0; disabling probe-based failure detection on it. In order to post comments, please make sure JavaScript and Cookies are enabled, and reload the page.

However, hme0 does not have a test address configured. Thus, the interface receives the sokaris configuration that it would have received after system boot.

IP network multipathing IPMP provides physical interface failure detection and transparent network access failover for a system with multiple interfaces on the confiiguration IP link. For a description of all error messages that are logged on the console during failures and repairs, see the in. IP Security Architecture Reference.

A single interface can be configured in its own IPMP group. The recipient of these addresses is a functioning interface in the failed interface’s IPMP group.

IPMP detects the following types of communication failures:. The ip kernel module, which implements the ioctldoes the network access cofniguration transparently and automatically. Configure an IP interface into standby mode. A L2 broadcast domain typically maps to a specific subnet. Instead, these failovers might choose an active interface with fewer data addresses that are configured as UP than the standby interface.

Likewise for logical interface and test address.

Author: admin