ISO 16047 PDF

according to test requirements such as BS Pt. 2 or ISO This can be expressed in two ways, the Coefficient of Friction µ and the Torque Coefficient (K . ISO FASTENERS – TORQUE/CLAMP FORCE TESTING. DIN EN ISO Fasteners – Torque/clamp force testing (ISO + Amd ) (includes Amendment).

Author: Vitaxe Kisho
Country: Moldova, Republic of
Language: English (Spanish)
Genre: Literature
Published (Last): 4 January 2009
Pages: 261
PDF File Size: 5.38 Mb
ePub File Size: 16.97 Mb
ISBN: 711-2-34023-845-2
Downloads: 72764
Price: Free* [*Free Regsitration Required]
Uploader: Dakazahn

By repeating 10647 test on a sample of the fasteners, the variation in the torque-tension relationship, can be established for an application. Eddy current method phase sensitive. Galvanised reference parts do not rust in storage. This service is not available if you are a URL user where you do not log in with an email address.

Coefficients of friction calculated according to ISO standard need to be regarded with caution, however. On some test benches the partial torque is measured in the thread, in others on the base. With these fasteners a washer is iao onto the kso the subsequent cold forming in which the thread is rolled into the surface ensures that this washer cannot fall off. MEC can be perform tests on actual fastened assemblies to obtain torque-angle graphs and to establish the torque to reach the yield strength of the bolt.

We have capability to collect time synchronized data across multiple instruments and sensors including the following:. The relationship between input torque and induced tension in a specific fastener application can be determined by testing the fastener with a calibrated load cell and torque device. These are useful, for example in comparing the coefficients of friction of different coating systems.

Based on this data, the nut factor or total coefficient of friction can be calculated and used to evaluate the effect of various fastener finishes, coatings, lubricants and manufacturing processes. A web subscription provides an easy and izo access to standards, and you are guaranteed to always have the latest edition.

Please first verify your email before subscribing 160477 alerts.

  HIBRIDNI MOTORI PDF

ISO – Wilson-Garner Company

Standards Subsctiption may be the perfect solution. Standards Subscriptions from ANSI provides a money-saving, multi-user solution for accessing standards. This technique has a distinct advantage because the actual joint and fastener can be tested without compromising the joint stiffness through the introduction of a load cell.

1607 bolt that requires testing is screwed into the test bench and fixed with a reference bolt.

They can also be used to cover larger holes. Cross-cut test for adhesion. As the voice of the U. They are identified io torque and clamp force. In this it is also necessary to take into consideration the geometry of the fasteners — more precisely, the increase of the thread, its flank diameter and the diameter of the head contact.

The ISO standard enables different reference base plates or reference washers to be used. That may sound routine initially.

Product Validation, Verification and Testing

It can also be used in conjunction with FEA when a transfer of fluid causes a resultant force that needs to be considered when doing structural analysis. You need to log in before adding standards to the monitoring service. Every day, thousands upon thousands of screws and bolts are used to fasten components together. Not only can FEA show where new parts may have potential issues, it can be used to diagnose failures seen in the field, and also to optimize designs in order to reduce cost.

Some of the capabilities 1604 Matrix Engineering Consultants include: However, 16407 the fastener and with it the washer is coated with a lubricant, the lubricated base of the fastener is tightened against the lubricated washer on the test bench. Monitoring Standards monitoring is a free service designed for you who wish to be alerted of changes to or new editions of the standards required in your work.

In order to achieve the desired clamp force with a specified torque, the tightening instructions must assume a total coefficient of friction of the 166047. Eddy current method amplitude sensitive. Similarly, varying degrees of roughness are possible for both types. Isso the document is 160477 or amended, you will be notified by email. Technical terms can not always be avoided. This ensures that you are always up-to-date and saves you both time and money.

  ARCHEXTERIORS 17 PDF

SCREW CONNECTIONS

The testing of fasteners with captive washers is not described in the standard. This standard is also available to be included in Standards Subscriptions.

When fastening, the torque must be correct in order to achieve the required clamp force — the force that a fastener uses to hold two components together. For hard bases the standard prescribes a narrow range of hardness, but permits a broad range of hardness for soft bases.

ISO 16047:2005

For example, brighteners in the galvanised coat serve to lower the friction between reference part jso fastener. If fasteners are lubricated, friction is reduced — this applies both with regard to both external lubrication via grease or wax and integrated lubrication via the addition of a lubricant to the coating. In practice, tightening instructions often specify fitting fasteners with a specific torque. Lso option of choosing between uncoated and galvanised bases reflects the prevailing procedures in the American and European areas.

The benefits of a subscription: You can download and open this file to your own computer but DRM prevents opening this file on another computer, including a networked server. The respective complementary partial torque can be identified via subtraction.

Nevertheless, coefficients of friction are determined for these parts. Webprint Printed and bound. This standard is not included in ieo packages. Need more than one copy?

However, galvanised reference parts have their own coefficient of friction.

A very low total coefficient of friction runs the risk of the fastener working itself loose. If you need to be able to add standards to the monitoring service, you must register as a user with your own username and password.

Author: admin